Hill Air Force Base

Sort By

Category

Show Advanced Options

Clear Filters |

260106-F-OD616-1006

Brig. Gen. G. Hall Sebren Jr., incoming Ogden Air Logistics Complex commander, speaks during an assumption of command ceremony on Jan. 6, 2026 at Hill Air Force Base, Utah. As commander of Ogden ALC, Sebren will lead a team of approximately 8,100 personnel who perform depot repair, overhaul, and modification of the A-10, C-130, F-16, F-22 and T-38 aircraft, the Minuteman intercontinental ballistic missile system, and a wide range of commodities.(U.S. Air Force photo by R. Nial Bradshaw)

Details Download

Official Portrait

This is the official portrait of Brig. Gen. G. Hall Sebren, Jr..

Details Download

251211-F-OD616-4058

Members of the 775th Civil Engineer Squadron suit up during the Bison Forge 25 1 readiness training exercise Dec. 10, 2025, at Hill Air Force Base, Utah. The exercise evaluated the wing’s ability to detect, overcome and execute mission requirements under challenging conditions. (U.S. Air Force photo by R. Nial Bradshaw)

Details Download

251211-F-OD616-4038

Members of the 775th Civil Engineer Squadron prepare a robot for a training scenario during the Bison Forge 25 1 readiness training exercise Dec. 10, 2025, at Hill Air Force Base, Utah. The exercise evaluated the wing’s ability to detect, overcome and execute mission requirements under challenging conditions. (U.S. Air Force photo by R. Nial Bradshaw)

Details Download

251211-F-OD616-4033

Members of the 75th Air Base Wing Inspection Team huddle during the Bison Forge 25 1 readiness training exercise Dec. 10, 2025, at Hill Air Force Base, Utah. The event marked the start of a series of readiness activities leading into 2026, including a Combat Readiness Inspection in February. (U.S. Air Force photo by R. Nial Bradshaw)

Details Download

251211-F-OD616-4030

Members of the 75th Air Base Wing Inspection Team observe Fire and Emergency Services and support personnel interacting during the Bison Forge 25 1 readiness training exercise Dec. 10, 2025, at Hill Air Force Base, Utah. The event marked the start of a series of readiness activities leading into 2026, including a Combat Readiness Inspection in February. (U.S. Air Force photo by R. Nial Bradshaw)

Details Download

251211-F-OD616-4024

A robot operated by the 775th Civil Engineer Squadron uses a camera to observe a small Unmanned Aerial System on the ground during the Bison Forge 25 1 readiness training exercise Dec. 10, 2025, at Hill Air Force Base, Utah. The exercise evaluated the wing’s ability to detect, overcome and execute mission requirements under challenging conditions. (U.S. Air Force photo by R. Nial Bradshaw)

Details Download

Hill Aerospace Museum uses 3D technology

Brandon Hedges, Hill Aerospace Museum's restoration chief, shows a 3D-printed part on an A-1 Skyrider flap Sept. 12, 2025, at Hill Air Force Base, Utah. The technology has delivered an 80% cost savings and saved hundreds of hours since the museum acquired the printers and scanners for restoration and exhibits. (U.S. Air Force photo by Cynthia Griggs

Details Download

Hill Aerospace Museum uses 3D technology

John Sluder, Hill Aerospace Museum exhibit specialist, shows 3D-printed parts printed for exhibit sign mounts Sept. 12, 2025, at Hill Air Force Base, Utah. The technology has delivered an 80% cost savings and saved hundreds of hours since the museum acquired the printers and scanners for restoration and exhibits. (U.S. Air Force photo by Cynthia Griggs)

Details Download

Hill Aerospace Museum uses 3D technology

Brandon Hedges, Hill Aerospace Museum's restoration chief, describes how 3D printers were used to restore the F-117 Nighthawk Sept. 12, 2025, at Hill Air Force Base, Utah. The technology has delivered an 80% cost savings and saved hundreds of hours since the museum acquired the printers and scanners for restoration and exhibits. (U.S. Air Force photo by Cynthia Griggs)

Details Download

Hill Aerospace Museum uses 3D technology

John Sluder, Hill Aerospace Museum exhibit specialist, shows organization containers printed with 3D technology Sept. 12, 2025, at Hill Air Force Base, Utah. The technology has delivered an 80% cost savings and saved hundreds of hours since the museum acquired the printers and scanners for restoration and exhibits. (U.S. Air Force photo by Cynthia Griggs)

Details Download

Hill Aerospace Museum uses 3D technology

John Sluder, Hill Aerospace Museum exhibit specialist, talks about one of the 3D printers the museum acquired to restore parts and to enhance exhibits Sept. 12, 2025, at Hill Air Force Base, Utah. The technology has delivered an 80% cost savings and saved hundreds of hours per project. (U.S. Air Force photo by Cynthia Griggs)

Details Download

Hill Aerospace Museum uses 3D technology

A 3D-printed turbosupercharger cooling cap for a B-24 Liberator sits in the upper turbosupercharger, with the original cap below, at the Hill Aerospace Museum, Hill Air Force Base, Utah, Sept. 12, 2025. The museum's restoration facility purchased 3D scanners and printers to support in-house preservation when original parts cannot be found. (U.S. Air Force photo by Cynthia Griggs)

Details Download

Hill Aerospace Museum uses 3D technology

A 3D-printed turbosupercharger cooling cap for a B-24 Liberator sits beside the original part at the Hill Aerospace Museum, Hill Air Force Base, Utah, Sept. 12, 2025. The museum's restoration facility purchased 3D scanners and printers to support in-house preservation when original parts cannot be found. (U.S. Air Force photo by Cynthia Griggs)

Details Download

Hill Aerospace Museum uses 3D technology

The restoration facility behind the Hill Aerospace Museum at Hill Air Force Base, Utah, uses 3D scanning and printing to replicate aircraft parts that cannot be acquired and to enhance exhibits. The technology has delivered an 80% cost savings and saved hundreds of hours per project. (U.S. Air Force photo by Cynthia Griggs)

Details Download

ALS Class 26-A

Airmen enrolled in Airman Leadership School Class 26-Alpha were honored during a graduation ceremony Dec. 4 at The Landing.

Details Download

ALS Class 26-A

Airmen enrolled in Airman Leadership School Class 26-Alpha were honored during a graduation ceremony Dec. 4 at The Landing.

Details Download

Team Hill and community work together to provide food pantry amid government shutdown

Volunteers unload deliveries of food and supplies donated by the community to aid airmen, government civilian employees, and families during the government shutdown. (U.S. Air Force photo by 1st Lt. Rachel Shaffer)

Details Download

Team Hill and community work together to provide food pantry amid government shutdown

Volunteers unload deliveries of food and supplies donated by the community to aid airmen, government civilian employees, and families during the government shutdown. (U.S. Air Force photo by 1st Lt. Rachel Shaffer)

Details Download

Team Hill and community work together to provide food pantry amid government shutdown

Volunteers unload deliveries of food and supplies donated by the community to aid airmen, government civilian employees, and families during the government shutdown. (U.S. Air Force photo by 1st Lt. Rachel Shaffer)

Details Download